Post Disclaimer
The information contained in this post is for general information purposes only. The information is provided by kubota l3400 won't start and while we endeavour to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the post for any purpose.
Make sure there is good voltage at the lift pump. If the actual problem is this, it should be solved by this method. Do it for at least fine munities. 352K views 6 years ago if your Kubota tractor won't start watch this video - and try this first. It may not display this or other websites correctly. Kubota L3540 Won't Start. You must log in or register to reply here. The other switches to look for are on the clutch pedal, on the range shifter if it is a standard shift or one just above the center of the floor board if it is a hydrostat. Today went to start the tractor and it won't start. Or if there is any faulty safety switch, it needs to replace too. Lights can still work with a dead (actually low voltage) battery. THe tractor will turn over but will not start. I followed the ignition procedure, indicator lights are fine, but when I turn the key I just get one beep followed by nothing, no clicks, nothing. The ignition lights and dash lights turn on with the key on but the engine does not turn over. Is your 3400 a hydrostat or standard shift transmission? If it is, you need to replace it. Kubota L3400 2006 will turn over but not start. If this is HST, rock your forward/reverse pedal back and forth while holding the key in the crank position. Battery fully charged, clicks when key is turned, but not engaging or spinning. Firstly, check the fuel line. JavaScript is disabled. If your Kubota diesel engine does not start, begin by confirming that your electrical and fuel delivery systems are performing properly. Then start with the battery. I had two separate things affect starting on mine. It may not display this or other websites correctly. Mechanical: Chassis: 4x2 2WD : 4x4 MFWD 4WD: Differential lock: rear standard: Steering: I followed the ignition procedure, indicator lights are fine, but when I turn the key I just get one beep followed by nothing, no clicks, nothing. It could be your fuel pump, but more likely it's your solenoid. It may not display this or other websites correctly. Press J to jump to the feed. It drives power from the tractor to the PTO-driven machine. For a better experience, please enable JavaScript in your browser before proceeding. Kubota Tractor won't startTry This - YouTube Press J to jump to the feed. What this does is, it pulls the fuel and takes it to the engine from the fuel tank. People need to turn off the vehicle to operate it again. .Sometimes it starts, then dies. I am thinking the fuel solenoid is bad or could it be the relay not supplying enough power to solenoid to get it to work? TractorData.com Kubota L3400 tractor information Ask an Expert Car Questions Agriculture and Farm Equipment This answer was rated: Kubota L3400 starter wont engage. If its still on, check for the cable which runs from the PTO shift and goes into the transmission case under the seat. Create an account to follow your favorite communities and start taking part in conversations. tested the solenoid and it works. I thought with a dead battery I would hear clicking, when turning the key. Turned on the engine and let it idle for a few minutes until it sounded better. The safety switch on the foot pedal has been a problem. The more I read about fuel solenoid the more I think my tractor non-run problem may be related to the fuel solenoid. Established in 2009, we are the largest online community of Kubota tractor and equipment owners. Turn the dial to the lowest setting in the resistance mode in the ohms portion of the meter. Electrical System Check Electrical issues are among the most common reasons for engines not starting. Welcome. Reading battery voltage with no load, does not tell the whole story. if it is good, in other words it doesnt drop below about 11 volts. The hold in coil is usually tied into low oil pressure, high temperature, sensors to shut the engine down if there is a problem develop when it's already running It should solve the problem. Kubota L3540 Won't Start : r/kubota - reddit.com Though it is a renowned brand, unfortunately, there are some problems you may face. You will feel like this is a new vehicle you are running. Fix all the connections battery has with other parts of the vehicle. kubota L3500 cranks but won't start (EDIT) not 3500, L3400, and i think he said it was a 2008 model. Join us in searching for a Kubota diesel that will not start in the cold weather. Kubota Diesel Engine Troubleshooting - Bobby Ford Tractor & Equipment Always consult equipment operator's manual and follow safety instructions before operating or servicing any tractor or equipment, or attempting any task. This sub Reddit is meant for everything and all things tractor and tractor related things. Always consult equipment operator's manual and follow safety instructions before operating or servicing any tractor or equipment, or attempting any task. Kansas, Butler county, Just east of DooDah. For a better experience, please enable JavaScript in your browser before proceeding. You have found you high resistance problem. If not, try to see a professional who can fix the problem for you. Thank you Wolfman. Checking Engine Start System. Standard Transmission. The fuel solenoid shuts off fuel or engages linkage that controls fuel distribution. I hope this article has given you a solid idea of where to start. Anyone have any ideas on what to do next? I have a Kubota L3400 with Manual transmission, 4WD. The - JustAnswer Does that include lube? It is a multipurpose tractor that you can use in various ways. If not the you have your culprit. Kubota Tractor won't start. | Tractor Forum You can find it by following the fuel line back from the injection pump and the first thing you run into with wires is likely the lift pump. Yes, if the air was formed in the hydraulic system, it can be stopped completely. You must log in or register to reply here. Pulled fuel cut off solenoidstarts. Is the large wire on the starter near 12.6 volts? Shutting of Suddenly Arter Working for a While. The consent submitted will only be used for data processing originating from this website. Read somewhere that the fuel solenoid can cause the issue. Another common problem in Kubota is not getting started at all but just clicking. Secondly, check and inspect the fuel filter. The fuel solenoid is not clicking when the key is turned. I did try the fuel solenoid after I removed it and the rod does not move when starting the tractor. if it is very low there, then by all means clean/repair the connections. If there is any water mixed with the oil then the engine can stall. Thanks for this threadI was packing up today and this happenednever thought to mess with the pedal until I read this and it started up after a couple of pushes. Or bad battery connection(s). My Kubota l3400 tractor won't start. L3400 won't start - what might be wrong? - TractorByNet TONY, DID YOU CHECK THE PTO LEVER, CLUTCH PEDDLE SWITCH AND HIS THE BATTERY CHARGED UP GOOD NO LOOSE CONECTIONS AND SAFETY SWITCH UNDER SEAT. Removed the solenoid and the tractor started, had to restrict airflow since the fuel solenoid was not connected.. With the wires plugged into each other you have the tractor thinking that the PTO is always disengaged, therefore it will start with the PTO engaged. Most times I get no click from the solenoid. Crack a line at an injector and see if you have fuel when cranking the engine. Kubota L3400DT-IF 4 WD Tractor, Serial . LOL. I tried the solution proposed by crbr, rocking the transmission pedal - and it worked - made my day! The other was the switch that senses the neutral position of the hydro pedal. It happens when the spring load is seized up and does not slide properly. else. Hey guys. For a better experience, please enable JavaScript in your browser before proceeding. Read somewhere that the fuel solenoid can cause the issue. Battery is good. You must log in or register to reply here. Mechanic's Assistant: What is the complete model and serial number of your machine? It was fine then. If the tractor starts off good, works for some time, and suddenly stops while in use, the most common reason is fuel starvation. OrangeTractorTalks brings together Kubota enthusiasts from around the world, into one place, purpose built just for them. Some of our partners may process your data as a part of their legitimate business interest without asking for consent. Not starting, shutting off after some time, POT not turning on, and RPM slowing down are the common kubota l3400 problems. Luckily, all these parts are much less money than just one hour of labor. Unfortunately, not all tractor is perfect. L3400 won't start. Safety switch. Help please! - OrangeTractorTalks Check the gear compartment if something like stone or dried mud had stuck there. If the diesel fuel pours as it leaves the line, there may be something clogged in the line. I had it going on Wednesday for about 20 to 30 minutes pushing snow, and then came back a few hours later to do some more work, and it wouldn't start. Or your fuel system needs bleed out so leave the injector line loose and crank for a while. Was asked to take a look at this problem and was solved by installing Starter Relay Kit That he bought from john deer but will work on any tractor I would think. It generally happens when algae grow inside the fuel bowl. If not try the second one. JavaScript is disabled. if it is very low there, then by all means clean/repair the connections. follow that with all the safety switches in the path to engaging the start relay. Fuel flow issues are the most common reason for Kubota L3400 to stop working after running for a while. I figured I needed to bleed the system. I have problem but it is not the seat switch because the PTO continues to rotate whether I am on the seat or not. Removed the solenoid and the tractor started, had to restrict airflow since the fuel solenoid was not connected.. The first time it happened, it was 10 minutes before I figured it out. then put the leads on the clamp connections and read it there. You must log in or register to reply here. First, never use starting fluid in a diesel. Kubota L3400 starter wont engage. Battery fully charged, - JustAnswer It generally happens if there are any battery issues. My Kubota l3400 tractor won't start. Charged the battery, - JustAnswer Fuel flow issues are the most common reason for Kubota L3400 to stop working after running for a while. I'm smart and relatively mechanically inclined, but I don't have a lot of experience with diesel or tractors, much less diesel tractors. Press question mark to learn the rest of the keyboard shortcuts. Kubota L3400 is a farmers tractor which is a very vital part for some of them. or the starter engage, you need to know if it is the battery, or high resistance/ connection or something. so look for bad grounds. You are using an out of date browser. You have found you high resistance problem. If it is standard or Shuttle shift , there is a small micro-switch for the neutral of the Shuttle Shifter that does not make contact sometimes , I had to tweak mine slightly (micro-switch contact) once to get it to work correctly . I disconnected the two wires and plugged them into themselves and it started right away now it doesn't turn over at all. Any thoughts? if its filled with dirt and thick mud-like object, you need to replace the filter. RUBYRUSS only posted a day ago that there was a problem with his L3200. It needs to be properly functioned to do all the tasks is supposed to do. 61. Some times the solenoid engages other times not. You must log in or register to reply here. Kubota enthusiasts, hobbyists, and fans! My L2800 has done this since newjust not as much now, It has gotten better with age. Checked battery, fuses, fuel and all are good. Fuel tank is half full. The fuel solenoid is not engaging. L3400DT W/ LA463 FEL and L235DT W/ BF400 Loader. You need a multimeter to start checking voltages. My tractor is suffering this now, but I do know where to look to get it back running. From what you've posted thus far I'd leave the switch alone and start thinking the fuel shutoff solenoid (""it isn't clicking") is bad. The ignition lights and dash lights turn on with the key on but the engine does not turn over. Still no idea what to do next. Check for voltage there and if not figure out why. Press question mark to learn the rest of the keyboard shortcuts. That isn't an issue. Established in 2009, we are the largest online community of Kubota tractor and equipment owners. Create an account to follow your favorite communities and start taking part in conversations. Welcome. My pantleg occasionally catches the PTO lever on my L3400. Buts that's where the real. What happens here is, that every other gear works fine and when you try to use that particular gear. Thirdly, the problem can be in the fuel injector pump. Kubota L3400 Manuals | ManualsLib if your Kubota tractor won't start watch this video - and try this first. There are several ways to solve this problem. Thanks for the Kubota books site. So, if there is any link of blockage in it, it can also create a problem. The dash lights stay strong and do not dim when the key is turned. called kubota and other parts places, they have no idea what it is, can't find a pic of it anywhere, so we just put a switch on it for now. Continue with Recommended Cookies. Anything and everything about Kubota. Today it won't start. For a better experience, please enable JavaScript in your browser before proceeding. If you would like to change your settings or withdraw consent at any time, the link to do so is in our privacy policy accessible from our home page.. Kubota Tractor Don't Start? Try cleaning your battery post and ground cable. Not the clamp connections, directly on the post's have someone try to start the tractor, anything less than 10.5 or 11 volts indicates either a bad battery (high internal resistance, or sulphated) or a shorted/draggy starter. Or maybe one of the PTOs are engaged? For a better experience, please enable JavaScript in your browser before proceeding. Can someone pinpoint where the fuel solenoid is located on the L3400HST? Nonetheless, I'm the man of the farm, so this repair falls on me. Every 100 Hours. No one here can tell you much more without more information from trouble shooting. To view the purposes they believe they have legitimate interest for, or to object to this data processing use the vendor list link below. Any chance a pto is engaged? You must log in or register to reply here. So, you need to check the battery first if you are facing this kind of problem. My Kubota l3400 tractor won't start. You nailed it, it was the forward/reverse pedal, stuck out of neutral position. he kinda thinks the fuel pump went out, any way to test that, anything else i should do next, don't really know to much about tractors, but the only tractor place we have around here wants $900 to tow it, and $250 a hour to work on it. If voltages are all good when attempting a start, but starter will not engage, then battery voltage is not getting to the starter or the return path is high resistance/open. Manage Settings Check if it is dead or have any other problem. Thanks, thats what it was, the solenoid wasen't getting power, we worked on it all weekend, some weird relay thing died and isn't sending power to the solenoid. Got up the next day, no start. JavaScript is disabled. Sounds like an obstruction or bad lift pump. Put the solenoid back on and it would start but then die immediately. Air in the fuel line. It's diesel so it's probably either the injection pump or the lift pump. Why is my diesel engine stalling in Kubota L3400? Put the solenoid back on and it would start but then die immediately. Kubota has no idea what it is, and i'm not going to the place that gave me that quote, we jumped it for now. what I found was that not enough. Please post back. If it is the starter solenoid circuit that is preventing the starter, you can activate the starter at the starter, by bypassing the interlocking safety switches and activating it directly at the starter. 2023 TractorByNet.com | TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners. Sometimes it well run for a few seconds other times a few minutes. Try to understand what is the problem first. For a better experience, please enable JavaScript in your browser before proceeding. It will have issues over time as it is made for heavy-duty work. Might even be your key switch which controls the solenoid. There are 2 coils in there and when the switch is the start position, it puts power to the "pull in coil", when the switch drops into the run position it moves the current to the "hold in coil". Here are the symptoms: It could still be the battery. Evacuator Valve. I replaced the switch watch that video here: https://www.youtube.com/watch?v=TT0QN_xReOM The switch I got was for a 2013 L3800 Kubota TD-060-53902 yours may have a different number I did see some online but I would check your local Kubota dealer first. Checked battery, fuses, fuel and all are good. Not being able to use any particular gear is not a common problem, but it occurs sometimes. Battery fully charged, Curtis B., Technician 44,329 Curtis B., Technician 44,329 Satisfied Customers Two weeks ago is the last time I used my L3400. Do it again if you feel needed. My relatively new (71 hours) Kubota L3400 will not start. Sorry for being late, thanks everyone for the replies, we worked on it all this weekend and finally got it, it's some kind of relay that controls the fuel cut off solenoid, it's not sending power to it anymore.